Gasboy Atlas Technician Programming Quick Ref Instrukcja Użytkownika Pobierz pdf (Strona 2)

Call Gasboy Technical Support at: 1-800-444-5529

Greensboro, NC 27420 · Phone 1-800-444-5529 · http://www.gasboy.com

Function Code 22:

Reported Volume Decimal Point

0 = XXX.XXX***

1 = XXXX.XX (export only)

Function Code 24:

Hose Pressurization

0 = Off***

1 = 2 hours

2 = 1/2 hours

Note: Not available in U.S. gallons

configuration.

Command Code 12:

Pump Program

• Enter 12

• Enter Side #

1 = Side 1

2 = Side 2

• Enter Function Code (1-4)

• Enter Configuration Code

Function Code 1:

Two-Wire Pump ID

1-16 = (7*** for Side 1; 11*** for Side 2)

Function Code 3:

Side Exists

0 = Does not exist

1 = Exists***

Function Code 4:

PPU Options

0 = Level 1 price bar displays level

sent by console or Card Reader

IN Dispenser (CRIND

)***

1 = Normal

*** Default

† Must be programmed to ‘1’ in New

Jersey.

From Level 3

Command Code 13:

PIN Code Change

Press Enter after selections.

• Enter 13

• Enter Level # 1, 2, or 3

• Enter new PIN Code

Unit returns to Command Input Mode.

Command Code 15:

Function Code 1:

Preselect Time-Out

0 - 999 seconds

Function Code 2:

Pump Time Out

0 - 999 seconds

Function Code 3:

Beeper Time Out

0 - 999 seconds

Function Code 4:

Slowdown Valve

0 - 0.999 gallons

Command Code 17

Conversion Factor and Master

Reset

Select Function Code.

Function Code 1:

Conversion Factor

0 = No conversion factor***

1 = U.S. Gallons

2 = Imperial Gallons

3=Liters

Function Code 2:

Master Reset (Retains Totals)

0 = No Master Reset

1 = Master Reset

Command Code 18:

Pulse Output Configuration

• Enter 18

• Enter Function #

• Enter Configuration #

Function Code 1:

Volume PPU

1. 1 PPU

2. 10 PPU***

3. 50 PPU

4. 100 PPU

5. 1000 PPU

Function Code 2:

Volume Pulse Width

1. 0.5 ms

2. 1.0 ms

3. 2.0 ms

4. 4.0 ms***

5. 17.0 ms

6. 19.0 ms

7. 26.0 ms

8. 150.0 ms

Function Code 3:

Money Pulse Width

1. 0.5 ms

2. 1.0 ms

3. 2.0 ms

4. 4.0 ms***

5. 17.0 ms

6. 19.0 ms

7. 26.0 ms

Function Code 4:

Volume Suppression (at start of

sale)

1. 0.030***

2. 0.009

3. 0.000

Function Code 5:

Quadrature Pulse Option

0 = Disabled***

1=Enabled

Function Code 6:

Authorize After Pump Stop

0 = Disabled***

1=Enabled

Function Code 7:

Price Restore Option

0 = Disabled***

1=Enabled

*** Default

ATC Programming

• Turn ON the programming switch on

the ATC Controller board.

• Press 100 then Enter.

• Select Fuel Type and press Enter.

740 = Gasoline

840 = Diesel

730 = Default

• Firmware cycles through each

fueling position. Select Fuel Type

and press Enter.

• Turn OFF the programming switch

on the ATC Controller board.

• Press F2 to exit ATC Programming

Mode.

ATC Inspection

Modes

• From Manager Keypad, press an

ATC Function Code (see below)

when unit is idle.

• Press Enter and Meter Number, if

appropriate.

• Press F1 to exit ATC Inspection

Mode.

Function Code 200:

Real Time Transaction Mode

• Main Display = Gross Volume

• Volume Display = Net Volume

• Grade 1 PPU Display = Current

Temperature

Function Code 300:

Audit Last Transaction

• Main Display = Gross Volume

• Volume Display = Net Volume

• Grade 1 PPU Display = Average

Temperature

Function Code 301:

Display Volume Correction Factor

• Main Display = Meter Number

• Grade 1 PPU Display = Volume

Correction Factor

Function Code 302:

Display Fuel Density

• Main Display = Meter Number

• Grade 1 PPU Display = 730 Gas or

840 Diesel

Function Code 303:Display

Temperature

• Main Display = Meter Number

• Grade 1 PPU Display = Current

Temperatur e

Function Code 304:

Display Gross Totals

• Volume Display = Gross Volume

(most significant)

• Grade 1 PPU Display = Gross

Volume (least significant)

Function Code 500:

Display Software Version

Main Display = ATC Version

Error Codes

Code Description

20 Pulser Fail

Conversion Factor Changed/Not

Programmed

Two-Wire/Standalone Mode

Changed

26 Meter Not Calibrated

27 Side 1 Two-Wire ID Changed

28 Side 2 Two-Wire ID Changed

29 Pump Time-Out Error

31 Totals Data Error

32 Pulser Count Error

35 Configuration Data Error

Unit Type Configuration Code

Changed

37 PIN Code 1 Changed

38 PIN Code 2 Changed

39 Cash/Credit Option Changed

40 Master Reset Jumper in Place

41 Side Exists Option Changed

44 Pump Handle Up at Power Up

45 Preset Overrun (Minor)

46 Preset Overrun (Major)

Atlas

™

is a trademark of Gasboy

International. CRIND

is a registered

trademark of Gilbarco Inc.

1 2

Komentarze do niniejszej Instrukcji

Brak uwag

Gasboy Atlas Technician Programming Quick Ref Instrukcja Użytkownika Strona 2

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Gasboy Atlas Technician Programming Quick Ref